Filter your search results

Filter by occupational area












































































Filter by status of standard



Search results

Found 33 short duration training standards. The standards are sorted in alphabetical order.

If your search has too many results, leave out words such as ‘and’ or ‘the’ and try again.

Use the Download as CSV button to save these search results to your computer. We update these standards frequently, so you should check the website and download a new version regularly.

Bonding, taping and positioning insulation board

The purpose of training delivered against this standard is to provide candidates with a practical introduction to the fixing of insulation boards and how to position, bond and tape as per specification

Brick slip systems

The purpose of training against this standard is to provide candidates with knowledge of brick slip systems and what they are used for.

Brick soffit systems

The purpose of training against this standard is to provide the candidate with the knowledge and skill to be able to safely and effectively install brick soffit systems.

Carpentry Skills for Supervisors

This standard is in development and will be published shortly.

Cloak systems

This course standard will be superseded by the Specialist damp proof course cloak systems standard on 1 February 2019. Employers have until 20 May 2019 to make a grant claim against this course.

Co-ordinating brickwork requirements

The purpose of training against this standard is to provide the candidates with an overview of how the brickwork team integrates with the wider project team.

Cold weather working requirements for bricklayers

The purpose of training against this standard is to provide candidates with knowledge of the key requirements for bricklayers working in cold weather.

Fitting flush doors with patio and decking levels to create inside and outside spaces

This training standard is in development and will be published shortly

Forming of cavities and correct installation of ties

The purpose of training delivered against this standard is to provide candidates with the practical skill and knowledge to be able to safely and effectively construct a cavity, paying particular attention to the correct fixings of wall ties.

General site formed damp proof course

This standard will be superseded by the Specialist damp proof course cloak systems standard on 1 February 2019. Employers have until 20 May 2019 to make a grant claim against this course.

Helical bar installation

This standard is in development and will be published shortly.

Helical bar surveyor

This standard is in development and will be published shortly.

Heritage brickwork

This course standard will be superseded by the Brickwork conservation, controls and philosophies standard on 1 February 2019. Employers have until 20 May 2019 to make a grant claim against this course.

Industry standards and tolerances for bricklaying and related occupations

This training standard is in development and will be published shortly

Installing fire barriers and breaks

The purpose of training delivered against this standard is to provide candidates with the knowledge and skills to install fire barriers and breaks.

Introduction to movement joints

The purpose of training against this standard is to provide candidates with an introduction to the provision of movement joints in masonry construction.

Introduction to the interface with related structural operations

This standard is no longer eligible for a grant and will be withdrawn on 1 February 2019. Employers have until 20 May 2019 to make a grant claim.

Laying insulated form units

This course standard will be superseded by the Insulated concrete forms installation and use standard on 1 February 2019. Employers have until 20 May 2019 to make a grant claim against this course.

Masonry cutting and drilling

The purpose of this standard is to provide the candidate with the knowledge, safety procedures and skill to be able to cut and drill masonry with all types of cutting and drilling equipment.

Masonry support angle installation

The purpose of training delivered against this standard is to provide candidates with the knowledge and skill to be able to safely install a masonry support system.

Materials storage and protection

The purpose of training against this standard is to provide candidates with the knowledge to store and protect materials on site.

Mechanical and modern pointing systems

This training standard is in development and will be published shortly

Non standard and special brick

This training standard incorporates the standard for the Special bricks course. It is in development and will be published shortly.

Pre-cast components and fixings

This standard will be superseded by the Sills, coping, cappings and junctions standard on 1 February 2019. Employers have until 20 May 2019 to make a grant claim against this course.

Quality assurance and customer/client handover

The purpose of training against this standard is to give candidates an overview of the different systems and requirements in place to control the quality of work and the handover process to the client.

Repairing defective brick and block work

The purpose of training against this standard is to give candidates an overview of the different systems and requirements in place to control the quality of work and the handover process to the client.

Sills, copings, cappings and junctions

The purpose of training against this standard is to give an overview of sills, copings, cappings and junctions in masonry construction.

Special bricks

This course standard will be superseded by the Non standard and special bricks standard on 1 February 2019. Employers have until 20 May 2019 to make a grant claim against this course.

Specialist damp proof course cloak systems

The purpose of this standard is to provide the candidate with knowledge and understanding of specialist cloak systems and where and when they are used in the construction process of a building. This course standard includes Weep hole positioning standard.

Thin bed joint systems

This course standard will be superseded by the Types and uses of mortars used for brick and block work standard on 1 February 2019. Employers have until 20 May 2019 to make a grant claim against this course.

Transferring levels for bricklayers

This training standard is in development and will be published shortly

Types and uses of mortars used for brick and block work

The purpose of training against this standard is to provide candidates with an overview of the different mortar types and uses used in masonry.

Wind post installation

The purpose of training delivered against this standard is to provide candidates with the knowledge and skill to be able to safely and effectively install a windpost.