CITB has developed this standard in discussion with industry
Duration
Minimum 1 day of 6 learning hours
Purpose/Scope
This training standard is designed for candidates who supervise assessing hardened concrete for strength onsite primarily through core testing but with reference to other indirect non-destructive testing (NDT) methods.
Scope:
- characteristic strength of concrete
- assessment of strength when concrete supply is in doubt
- assessment for strength of specific locations where no information available
- principles of core and NDT methods
- planning for test locations and numbers
- assessing core results
- assessing in-direct NDT results
- assessing core results in conjunction with in-direct NDT
- review supplier and site pour records
- actions in the event of non-compliant concrete.
Occupational relevance
Training delivered against this standard would be relevant to the following occupational group(s):
- supervision
- management and leadership.
Candidate pre-requisites
There are no candidate pre-requisites as part of this standard. However a basic knowledge and experience of concrete would be beneficial.
Instruction/Supervision
As a minimum, course instructors must be able to demonstrate that, in relation to this standard, they have:
- a train the trainer or instructional techniques course certificate
- successfully completed training to this standard
- at least 2 years relevant industrial experience
- a verifiable CV.
Delivery
Delivery may be in a classroom environment.
All materials and equipment must be of a suitable quality and quantity for candidates to achieve learning outcomes, and must comply with relevant legislation.
The class size and candidate/instructor ratio must allow training to be delivered in a safe manner and enable candidates to achieve the learning outcomes.
This standard is considered to contain 51% or more theoretical learning.
Assessment
For the successful completion of training, candidates must complete an end of course practical assessment or knowledge test that measures the learning outcomes and has a pass or fail criteria.
Quality assurance
Quality assurance against this standard will require initial approval of the training organisation and their content mapped to the standard.
CITB will also conduct an approval intervention, either desk-based or centre visit, to ensure the training organisation can meet the requirements of the training standard.
Approved training organisations (ATOs) will be required to present information on records of training and assessment upon request to CITB for desk based analysis. They will also be visited annually by the CITB quality assurance team.
Renewal/refresher
There are no mandatory renewal or recommended refreshment requirements for this standard.
Approval date
November 2018
Review cycle
Either on request or in 3 years from approval date
Learning outcomes
| The candidate will be able to: | Additional guidance to support learning outcome |
|
Explain difference between strength assessment
for doubts in supply and specific locations
|
BS EN 13791, BS 6089,
Concrete Society CA47 Core testing
|
Plan assessment regime
|
|
Assess core and NDT results
|
|
Assess site and supplier records
|
|
| Conclude and record outcomes |
|
Additional information about this standard
Health & Safety Executive (HSE) guides:
Health & Safety at Work etc Act 1974
Health and safety in construction
Personal protective equipment a brief guide
PPE
PUWER
COSHH
RIDDOR
LOLER
CDM
Manual handling
Noise
Hand-arm vibration
Electrical
Legislation
http://www.legislation.gov.uk/:
- Health and Safety at Work etc Act (HSWA) 1974
- The Work at Height Regulations (WHR) 2005
- Work at Height (Amended) 2007
- Personal Protection Equipment (PPE) Regulations 2002
- Personal Protection Equipment (PPE) at Work Regulations 1992
- Provision and Use of Work Equipment Regulations (PUWER) (1998 UK 1999 NI)
- Control of Substances Hazardous to Health Regulations (COSHH )2002
- Lifting Operations and Lifting Equipment Regulations (LOLER) 1998
- Reporting of Injuries, Diseases and Dangerous Occurrences Regulations (RIDDOR ) 1995
- Construction (Design and Management) Regulations (CDM) 2015
- Construction (Health, Safety and Welfare) Regulations 1996
- Manual Handling Operations Regulations 1992 as amended 2002.